Electrofishing is a blast. Launch the boat, extend the electrodes, adjust, kick on the generator, set voltage and amperage, pull on the gloves, man a dipnet and step on the safety switch. Lean over the front rail and watch. 240 volts adjusted to 6 or 8 amps, and fish begin to appear, almost like magic. The scapper (the one who picks up the fish) goes to work, the net pierces calm water and the first fish is brought on board, quickly and gently deposited into the aerated live well. As the boat moves across the water, along shoreline, different sizes of different fish are collected and put into the live well for processing, soon. It's never hard to find help to go electrofishing!
I know, I know, it's November. In the North Country, pondmeisters likely are faced with a pretty thick layer of ice right now. If not, you soon will be. In the south, you face the beginning of winter. Holidays are on our minds, but in another month or so, we will all be looking forward to warmer months. So, let's sit back and think of spring. To a fisheries biologist, spring means it's time for largemouth bass electrofishing.
Earlier this year (Pond Boss, volume XIV, issue 5), Bill Cody and I related information on how largemouth bass abundance can be related to angling catch rates in ponds. Now, let's switch gears a little and relate bass abundance to electrofishing samples. I know there is a lot of curiosity out there when it comes to this standard fisheries sampling gear. So, let us show you how largemouth bass abundance in a series of South Dakota ponds was related to the numbers and sizes of largemouth bass that we caught by electrofishing. Along the way, we'll give an explanation how electrofishing works.
In the South Dakota study, 14 ponds had both abundance estimates (number of fish per acre) and electrofishing catch per hour. Ponds had surface areas that ranged in size from 0.8 acres to near 20 acres. As abundance of largemouth bass increased, so did the number we caught per hour of night electrofishing (Figure 1). While that probably is not a big surprise, you can see there is quite a bit of variation in catch rate at a given density. Look at about 45 bass/ acre - you can see that we caught about 10/hr in one pond but 70/hr in another pond. That could have been due to temperature, weather, amount of structure in the pond, or even water quality characteristics. Heck, maybe we had an inexperienced worker on the front of the boat who was not very good at dipping the bass. If water is too soft (low conductivity, low alkalinity, etc.) then our electrofishing equipment is not as effective. Similarly, when water gets too hard (high conductivity, high alkalinity, etc.), then we again are not as effective.
Electrofishing is one tool in our pond management tool kit. Those who haven't been around electrofishing episodes don't often know what to expect. Some folks think the boat is launched, the foot switch is engaged, and all the fish in the pond pop to the top and make their way to the boat. Kind of like a Pied Piper of fishing. It's not like that at all. Our mission when electrofishing is to collect a random sample of fish which is statistically reliable significant for that population. Catch rate is important to us, but maybe not quite as important as collecting enough fish to evaluate a given population at that time.
Now, switch focus to Figure 2. Look what happens to proportions of larger bass in the population sample as bass abundance increases. At low density, bass have less competition for available food, and tend to grow faster and larger. As abundance increases, growth and size structure declines. Biologists call this "density-dependent growth." Once we got to about 150/hr of largemouth bass, very few bass ever exceeded 12 inches. These high density populations represent the classic crowded or "stunted" bass populations. Dr. Jeff Slipke, a biologist with Southeastern Pond Management (an advertiser in Pond Boss), recently told us that 90% of the clients they visit for the first time have overly abundant largemouth bass. Ninety percent! Treatment? Selective harvest. Numbers of smaller bass must be removed, either by angling or by a professional biologist using an electrofishing boat. The goal is reduce bass density, increase their growth rates, and grow larger bass!
As we electrofish, the boat moves around the pond or lake, and we get to see a "snapshot" of what's going on underwater. These graphs define bass populations easily enough, but as electrofishing continues, we typically see a corresponding dip in quantities and sizes of forage fish. Too many bass are feeding on too few bluegill or other forage fish. As you can imagine, seeing small forage fish in an overcrowded bass pond is like seeing a golfer in a lightning storm. Neither one lasts very long.
What happens to the size structure of largemouth bass as the bass "biomass" (pounds/ acre) increases? While we only had biomass estimates for 10 ponds, you can see the same trend as for bass abundance (Figure 3). Once largemouth bass got to 1(X) pounds/acre, NONE of the fish we collected by night electrofishing were over 12 inches in length. Any pond can only support so many pounds of largemouth bass. Do you want those pounds as fewer, larger bass, or as big numbers of smaller bass?
Electrofishing allows biologists to paint a picture of population structures under water at a single point in time. This information is important for serious pond managers. Electrofishing, done at the right time, not only tells us the status of your fish population, but allows biologists to compare year to year, and project what will happen in months to come. Electrofishing can help decide whether or not to feed, or to adjust the habitat for different species or size ranges of fish.
Here are other pertinent points about electrofishing...different ponds respond differently to electrofishing. The limits of an electrofishing boat not only include water chemistry and conductivity, but also depths of the water. Most electrofishing boats work best in water less than six or seven feet deep. When fish are deep, electrofishing may not do the trick. That's why we work in spring and fall months when fish tend to be nearer the shoreline.
After all, we do want to get a sample of fish which tells the underwater tale of your pond's population.
While this process is fun we need to add some qualifier comments. Seriously, electrofishing is dangerous, and safety must be foremost in the mind of any operator. We always ensure all boat occupants wear life jackets, rubber gloves, and rubber boots. We don't want anyone to be part of an electrical circuit. Earlier in the article, we mentioned the safety switch. There typically are two safety switches on electrofishing boats. One is the power switch on the control unit operated by the boat driver. The dipper up front also has to step-on a switch to allow electricity to flow into the water. If that person falls forward into the water, the switch would disconnect, and there would be no electrical field in the water.
So there you have it.
The specific information discussed here involved relationships between bass abundance and electrofishing catches for our South Dakota sampling. Such relations also occur elsewhere across the country. The scale may change (that is, the numbers may be higher or lower) depending on geographic location and type of electrofishing equipment, but the relationships remain the same.
Class dismissed! Test Monday.
Reprinted with permission from Pond Boss Magazine
